How To Use A Shop Vac For Water Pump – Basic Instructions

Cleaning is always not about dry stuff; only you will need a shop vac capable of working as a dry and wet shop vac at the same time.

How to use a shop vac for water

In case you are wondering how to use a shop vac for the water pump, the first thing you should do is find out how to use a vacuum for general cleaning purposes. What is meant by this is that you should be aware of how to use a vacuum for more than just sucking up dust and dirt from your carpets. Shop vacs can be used to clean almost anything, as long as it has not been sealed or closed. It is as easy as that! The question is how to use a vacuum for a water pump.

The first thing to consider is determining if your shop vac has the functionality to work as a wet/dry shop vac. All of the shop vacs are not capable of water suction. So before running into wet floor cleaning or water suction jobs, make sure your shop vac is compatible with water suction.

The procedure works this way; almost every wet/dry shop vac can be used for water cleaning. The water is sucked into the tank of the shop vac, and then you need to empty the tank when it is filled.

Self-emptying shop vacs have a vent hose at the tank, so when the water is sucked into the tank, it will be drained out of the shop vac, and you don’t need to stop occasionally to empty the tank. You have to keep the vent cap open so that the water can drain while using shop vacs for wet cleaning.

One thing you must keep in mind, is the wet/dry shop vacs are not designed as an alternative to a water pump, but you can use them for cleaning stray water on the floor. If you use them for heavy-duty water suction, it might affect the shop vac’s motor performance and life. You can use your wet/dry shop vac for water suction occasionally but not for heavy-duty jobs.

It is not a pump and never will be. Make sure it is a Wet-or-Dry model. After removing the paper filter (use the foam filter) and cleaning it out, you can suck up water but not pump it. You need an actual liquid pump for that.

How to Use Shop-Vac as a Water Pump?

1- Attach the hose to your Shop Vac

To use your shop vac as a water pump, just put a hose from the shop’s outlet port into a larger pipe where you need water to go.

Attach the intake tube to the waste pipe – making sure that they are connected tightly. You can use a screwdriver to tighten the bolts holding the waste pipe firmly in place. You must start to tighten the bolts slowly to avoid damaging the pump.

2- Switch it ON

After you have completed these steps, you will be ready to attach the pump to the car’s carburetor. Turn on the engine and give it a couple of starts. Just switch it ON, and it will start. Depending on how much water you need to pump, you can get a little drill pump for small situations, and the hand pumps do pretty well and very portable. You may need to use the carburetor’s water pump clip to keep the pump from spinning. After the car has started moving, you can remove the pump. Follow how to use a vacuum for the water pump by following the same steps as you did with the intake tube.

You have to read the user manual and check if you need any special filter for this purpose, before using your shop vac for the first time with water.

Here is a very helpful video that explains the process clearly…..

Below is another video to show you the same process.

Cleaning the Shop Vac after using it for the water pump

Once you know how to use a vacuum for the water pump, the next step is to use a vacuum for cleaning. When dealing with water pumps, you are dealing with an array of moving parts – a few of these moving parts pumps. To get them cleaned, you need to turn off the water pump, remove the engine’s intake tube, and use a shop vac to suck up all the dirt and grease stuck in the intake tube.
The next thing to do is clear away any minor clogs formed in the intake tube. This includes cleaning out the back of the pump housing and any crevices on or around the pump itself. Once all the dirt and grime are removed from the pump housing, you can pour a small amount of silicone oil into the pump and allow it to lubricate. This should prevent any leaks in the future.
Next, remove the intake tube from the engine and set it aside. Connect the vacuum motor and the pipes to the water pump – you will need to identify the pipe or fitting that goes to the waste pipe. Start to tighten the bolts holding the pipes in position and secure them with washers. When you are satisfied that they are secure, tighten the washers again – but make sure they are not too tight. You will know when the pipe is adequately secured because you will see water leaking out.

Shop Vac Water Pump Instructions

Shop vacs are powerful enough to suck up water and not leave any sloshing mess behind. In fact, they’re often used to clean up after floods! However, in order to maintain the shop vac’s performance and keep it from clogging, it’s important to follow the manufacturer’s instructions for proper maintenance and cleaning of the filter. Filters can be reused if washed properly- just be sure to follow the instruction for cleaning your filters!

Although some people might find the Moosoo Small Quiet Shop Vac Review to be a little too small, it is still a powerful and affordable machine. The vacuum is easy to use with just four basic steps: Fill up the tank, add detergent if there is a dedicated tank (optional), clean with appropriate settings on the vac and attachments of your choice, empty and rinse the tank before storing away. Remember to use the correct filter for the task at hand in order to avoid clogged filters and a shortened vacuum life.

Moosoo Small Quiet Shop Vac is a great option for people who are looking for an inexpensive and easy-to-use shop vac. It has a very attractive design and it’s very quiet. However, users should remember to empty the canister at the end of each use and more often for big tasks. They should also check the hoses and accessories for debris or blockage, and brush or blow air intake ports so that it’s ready for the next task.

How water pumps work

When you think about using a vacuum for a water pump first, you must understand how pumps work. The water used to operate a pump is passed through a filter made of plastic or metal. This filter will remove impurities that are smaller than the holes through which the water passes. Once this has been done, the pump is ready to work.

How water pumps work is very simple, although it is not exactly the simplest way a device designed to function this way could be understood. Consider how a car engine works. First, the engine burns fuel to move the car; then, through a set of complex pumps, the fuel is burned at an extremely high temperature in the crankcase (at this point, you might think the concept breaks down, but it doesn’t). Then, when the fuel is burned, it cools and is recycled. So, essentially the same process is at work in both the engine and water pumps on a power plant.

How To Suck Up Water With A Shop Vacuum

You can suck up water and even a variety of liquids other than those of flammable liquids, with a shop vac.

You need to make some minor alterations before using your shop vac with wet objects. The shop vacs act differently with dry objects and wet objects. While cleaning dry objects the vacs use to filter and bags. While using your shop vac with water you need to take off the filter bag. Almost every shop vac is designed to be used with water.

Can You Use A Shop Vac Without A Filter?

This is something that every shop vac holder must know. Yes, you can use a shop vac without a filter but only in case when you are using it for picking up water spills. If you are using your shop vac without a filter you may end up finding clogged debris in your shop vac canister. This is not a good practice to use a shop vac without a filter. This will result in damaging the performance of your vacuum.

Can You Use A Shop Vacuum Without A Bag?

A wet/dry shop vac comes with two settings, one with a bag and the other without the bag. You must use a vacuum bag while you are cleaning dry stuff. You have to remove the bag to suck up wet materials or water spills.